JAI SW-8000Q-SFP

Specifications for SW-8000Q-SFP Sweep+ Series Scanning system 4 high-speed CMOS line sensors, prism-mounted Active pixels 4 x 8192 pixels (R, G, B, NIR) Line rate (full width) Up to 36 kHz (variable) for 8-bit RGB + NIR 37 kHz possible with YUV compression Sensor width 30.72 mm Pixel size 3.75 µm x 5.78 µm Ethernet speed 10GBASE-SR / 10GBASE-LR / 10GBASE-ER Video output Single stream: RGBa8 Two streams: RGB8, RGB10V1Packed, RGB10p32, YUV422_8_UVYV, YUV422_8 (visible) Mono8, Mono10Packed (NIR) bbbbbb illuminance (min.) 214.5 lx @ 7800 K (Gain 18 dB, 525 µs exp., 50% video, f/2.8) Responsivity RGB: 41 DN/nJ/cm2 @ 550 nm (G channel) NIR: 24 DN/nJ/cm2 @ 800 nm (10-bit, 0 dB gain) S/N ratio >53 dB on green, 10-bit with 0 dB gain >55 dB on NIR, 10-bit with 0 dB gain bbbbbs (Trigger) 1 Opto In + 1 TTL via 12-pin, 2 TTL via 10-pin, Pulse Generator (4), NAND Out (2), bbbbbb (4), User Out (4) Outputs 2 TTL via 12-pin, 2 TTL via 10-pin Gain Digital Master: 0 to +30 dB, R/B/NIR: -4 to +12 dB Digital Individual: 0 to +36 dB White balance Manual/one-push auto by gain or exposure (4000K - 9000K) 3 Presets (5000K, 6500K, 7500K) Gamma 0.45 to 1.0 (9 steps) or 257-point LUT Image processing PRNU/DSNU, black level, flat shading and color shading correction, chromatic aberration adjustment, horizontal mirroring, noise filtering Color space conversion RGB or RGBa8 to HSI, XYZ (CIE), sRGB, Adobe RGB, or User Custom RGB Exposure modes No shutter, timed, and trigger width control Electronic shutter 3 µs to 27778 µs in 1 µs increments at 36 kHz. Exposure time can be longer at slower line rates. Pulse width control 1.8 µs to ~1 sec Time synchronization Support for Precision Time Protocol (IEEE 1588) Lens mount Nikon F-mount or M52 mount (46.5 mm flange back for both mounts) Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing) Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing) Vibration 3G (20 Hz to 200 Hz, XYZ directions) Shock 50G Regulations CE (EN61000-6-2, EN61000-6-3) FCC Part 15 Class B, RoHS/WEEE Power 12-pin PoE +10V to +25V DC. 17.4 W typical @ 12V Not supported. Dimensions (H x W x L) (without connector and lens mount protrusions) 90 mm x 90 mm x 120 mm Weight 980 g Specifications SW-8000Q-SFP SW-8000Q-SFP-F SW-8000Q-SFP-M52 4-CMOS prism line scan camera with F-mount 4-CMOS prism line scan camera with M52 mount Ordering Inbbbbation Dimensions (F-mount) Connector pin-out DC In / Trigger SFP+ Interface HIROSE HR10A-10R-12PB(71) Pin 1 Ground 2 DC in +10V to +25V 3 Ground 4 Reserved 5 Opto in 1- 6 Opto in 1+ 7 TTL out 4 8 NC 9 TTL out 1 10 TTL in 1 11 DC in +10V to +25V 12 Ground Spectral response SW-8000Q-SFP Sensitivity Wavelength (nm) Relative Response Visit our website on www.jai.com Europe, Middle East & Africa Asia Pacific Americas Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444 Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300 Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners. JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. August 2020 F-mount model shown. For M52 drawings and dimensions, see manual. SFP+ transceiver module must support: • 10GBASE-R • Power level 1 Maximum fiber optic cable lengths » 10GBASE-SR: 300m (cable type OM3) » 10GBASE-SR: 400m (cable type OM4) » 10GBASE-LR: 10km (cable type OS2) » 10GBASE-ER: 40km (cable type OS2)