产品详情
LC300/630II机械密封
自贡市川密机械密封件有限公司专业制造襄阳五二五浆液循环泵LC机械密封
LC机械密封安装使用要求
1、设备转轴的径向跳动应<=0.04毫米，轴向窜动量不允许大于0.1毫米；
2、设备的密封腔部位在安装时应保持清洁，密封零件应进行清洗，密封端面完好无损，防止杂质和灰尘带入密封部位；
3、在安装过程中严禁碰击、敲打，以免使机械密封磨擦会破损而密封失效；
4、安装时在与密封相接触的表面应涂一层清洁的机械油，以便能顺利安装；
5、安装静环压盖时，拧紧螺丝必须受力均匀，保证静环端面与轴心线的垂直要求；
6、安装后用手推动动环，能使动环在轴上灵活移动，并有一定弹性；
7、安装后用手盘动转轴，转轴应无轻重感觉；
8、设备在运转前必须充满介质，以防止干磨擦而使密封失效；
常见泵号如下：
LCF40/250I LCF40/350I LCF40/400I LCF40/450I LCF50/350N2 LCF50/400I LCF50/460I LCF65/310I LCF65/315I LCF65/350I LCF65/400I LCF80/400I LCF80/450I LCF100/300 LCF100/320I LCF100/350I LCF100/420I LCF125/405I LCF150/300I LCF150/350I LCF200/300I LCF100/500T LCF150/400I LCF200/410I LCF250/430I LCF250/430I
LC300/500I LC300/530I LC300/400I LC300/635I LC300/630I LC350/500I LC350/560I LC400/500I LC400/540I LC450/635I LC500/630I LC550/700I LC550/710I LC550/750I LC600/800I LC600/825I LC700/900I LC700/898I LC800/1000I LC900/1150I
LC300/500II LC300/530II LC300/400II LC300/635II LC300/630II LC350/500II LC350/560II LC400/500II LC400/540II LC450/635II LC500/630II LC550/700II LC550/710II LC550/750II LC600/800II LC600/825II LC700/900II LC700/898II LC800/1000II LC900/1150II
密封型号：
HTM-30S215Z(Q) HTM-30S315Z(Q) HTM-30S220Z(Q) HTM-30S330Z(Q) HTM-30D251ZZ(XX) HTM-30D315ZZ(XX)
HTM-40S215Z(Q) HTM-40S315Z(Q) HTM-40S220Z(Q) HTM-40S330Z(Q) HTM-40D251ZZ(XX) HTM-40D315ZZ(XX)HTM-55S215Z(Q) HTM-55S315Z(Q) HTM-55S220Z(Q) HTM-55S330Z(Q) HTM-55D251ZZ(XX) HTM-55D315ZZ(XX)HTM-60S215Z(Q) HTM-60S315Z(Q) HTM-60S220Z(Q) HTM-60S330Z(Q) HTM-60D251ZZ(XX) HTM-60D315ZZ(XX)HTM-80S215Z(Q) HTM-80S315Z(Q) HTM-80S220Z(Q) HTM-80S330Z(Q) HTM-80D251ZZ(XX) HTM-80D315ZZ(XX)
LB-LK7-120S LB-LK7-120D LB-LK6-115S LB-LK6-115D
HTM-30S HTM-40S HTM-55S HTM-60S HTM-80S
HTM-30D HTM-40D HTM-55D HTM-60D HTM-80D
HR3-125 HR3-142 HR3-158 HR3-175 HR3-198
HR325/230 HR325/210 HR325/190 HR325/170
HRM-125D3 HRM-142D3 HRM-158D3 HRM-175D3 HRM-198D3
HRM-125S3 HRM-142S3 HRM-158S3 HRM-175S3 HRM-198S3
HMR3C-125 HMR3C-142 HMR3C-158 HMR3C-175 HMR3C-198
LC300/630II机械密封
