FDJ-230煤矿钢管切割锯厂家

FDJ-230煤矿钢管切割锯厂家

产品概述：

风动手持切割锯是我公司针对高危，安全系数要求特别高的工作环境，如化工.治炼厂.天然气开采.高危潮湿的隧道，水下及狭窄的空间作业，尤其是高瓦斯防爆矿井。

山西万泽锦达矿山机械设备有限公司自主研发的新型多用途风动手持切割工具。它使用台湾进口气动马达作为动力输出，利用压缩空气作为动力源，不用电源。风动手持切割锯不但整机重量轻，操作简单，携带方便零火花，提高工作效益。本产品安全可靠是高危行业的气动切割工具。

特点:
    适合锯切各种钢管、铝型材、铜、铁等金属管材棒材。切断面平整,精度高.
冷却循环系统,使工件切面光洁准确，无毛边,提高锯片使用寿命,适合多量长时间锯切。

产品技术参数：

品牌：万泽锦达  

型号：FDJ-230 

类型：手用锯条锯片     

表面处理：半抛镀铬

全长：1350mm   

宽度：15mm     

齿距：0.2mm         

厚度：0.1mm      

锯路宽：1200mm

为了安全作业需要注意以下几点：
1、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命
2、关闭空气马达时，释放阀杆。

3、更换锯片前，务必断开空气软管，并推动阀杆以释放掉马达内的压力。

4、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。

5、下次切割开始前，锯片必须保持运动状态。气动锯时，锯片不能接触任何表面。

6、了解所需切割的材料，如有必要可以通过降低空气压力来降低锯片的转动速度。

7、确保牢固固定了所需切割的材料，防止其移动。

8、气动空气马达时，用手指按压阀杆，然后开始切割。

9、断开空气软管时，关闭空气软管阀。断开前，先打开空气阀给软管减Product overview:
Pneumatic hand cutting saw is my company for high risk, safety factor particularly demanding work environment, such as chemical. Refinery. Natural gas mining. High risk wet underwater tunnel, and narrow space operations, especially in high gas coal mine explosion.
Shanxi million of new multi Zejin pneumatic mining machinery and equipment limited company independent research and development of hand-held cutting tools. It uses Taiwan imported pneumatic motor as power output, uses compressed air as power source, and does not use power. The pneumatic handheld cutting saw is not only light in weight, simple in operation and convenient to carry zero spark, but also to improve work efficiency. This product is safe and reliable. It is a pneumatic cutting tool in high risk industry.
Characteristic:
It is suitable for cutting all kinds of steel pipe, aluminum, copper, iron and other bl pipe rod. The cutting section is smooth and the precision is high.
The cooling cycle system makes the cutting surface of the workpiece accurate and accurate, without edge, and improves the service life of the saw blade, and is suitable for a long time sawing.
Product technical beters:
Brand: up to Zejin million
Model: FDJ-120
Type: hand saw blade
Surface treatment: semi cast chromium plating
Full length: 1350mm
Width: 15mm
Tooth distance: 0.2mm
Thickness: 0.1mm
Sawing b: 1200mm
In order to work safely, we need to pay attention to the following points:
1, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life
2. When the air motor is closed, the stem is released.
3. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
4, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
5. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
6, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
7, ensure that the required cutting material is firmly fixed to prevent its movement.
8. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
9. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.