产品详情
Santoprene 121-85M100 美国三都坪 TPV
我公司长期代理销售三都坪Santoprene塑胶原料
我们的宗旨：
服务热线：13686017791 易小姐
塑料- 影响着每天的日常生活
就增长速度而言，没有哪一种用量相当的材料能够与塑料相提并论。世界各地的塑料需求量增长速度均高与各国国内生产总值的增长速度。究其原因，那就是如果我们想满足日常生活需求，并且让生活越来越舒适，塑料是我们的不二选择。对于食品包装和运输、房屋的建造和保温、家用电器、交通或休闲活动等领域的应用，塑料都是首选材料。
美国三都坪TPV
TPV有轻微的吸湿特性，应补充干燥，特别是在进行挤塑或吹塑加工前，更要进行干燥。在把材料放到干燥箱中之前，应当先把干燥器的温度升高到100℃。然后使TPV在干燥箱中保持2-3小时。 应避免与相对湿度高的环境接触，因为材料会吸收水分，使加工的产品产生空洞。如果在停机较长的时间之后，在重新开始操作之前，应当把挤塑机筒内所存留的原料排出。在加工TPV之前和之后，应当把挤塑设备彻底清理干净。注塑设备或挤塑机机筒应当以机械方式清理或者用聚乙烯或聚丙烯彻底置换排空。
1）注塑加工
TPV的熔体粘度比许多种普通热塑性材料更大，在加工时，需应用较大的注料嘴、注料口、流道和浇口，还需要采用高的注射压力和较快的注射速率，以提高充模速度和减少飞边，此后在较高的压力下有一个短的保持时间，使之足以将浇料口冻结。 注射螺杆的速度应当是100至200转/分，背压力在不需要混合时应当尽可能低。
2）挤塑加工
不需要真空定径。建议采用长径比为28比1或更大比例的挤塑机。通常单段螺杆比为3比1左右，如果需要用筛网组合，可用20至60网目的筛网。最好将熔体温度保持在规定范围的下限，使挤塑产品的质量最优。
3）吹塑加工
TPV机械操作条件要求与注塑和挤塑所规定的相同。模具设计、型坯尺寸、加工周期时间、以及壁厚均匀等吹塑加工因素都与制件的几何形状有很大的关系。熔体加热过度将使牵伸比下降，应当避免过热。
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Specific Gravity | 0.970 g/cc | 0.970 g/cc | 23°C; ASTM D792 |
| Mechanical Properties | Metric | English | Comments |
| Hardness, Shore A | 62 | 62 | 2 mm, 15 sec; ISO 868 |
| 67 | 67 | Air at 302°F, 168 hr; ASTM D573 | |
| Tensile Strength at Break | 4.50 MPa | 653 psi | Air at 302°F, 168 hr; ASTM D573 |
| 5.00 MPa | 725 psi | Across Flow; ASTM D412 | |
| Tensile Stress |
2.10 MPa @Strain 100 % |
305 psi @Strain 100 % |
Across Flow; ASTM D412 |
| Elongation at Break | 440 % | 440 % | Across Flow; ASTM D412 |
| 475.2 % | 475.2 % | Air at 302°F, 168 hr; ASTM D573 | |
| Tear Strength | 36.1 kN/m | 206 pli | 73°F, Die C; ASTM D624 |
| Compression Set | 18 % | 18 % | 73°F, 22 hr; ASTM D395 |
| 39 % | 39 % | 257°F, 70 hr; ASTM D395 | |
| Electrical Properties | Metric | English | Comments |
| Dielectric Constant | 2.7 | 2.7 | 1.96 mm; ASTM D150 |
| Dielectric Strength | 25.6 kV/mm | 650 kV/in | 2.03 mm; ASTM D149 |
| Thermal Properties | Metric | English | Comments |
| Maximum Service Temperature, Air | 135 °C | 275 °F | |
| Brittleness Temperature | -60.0 °C | -76.0 °F | ASTM D74 |
(以上数据仅做网络参考，详情请QQ、电话或微信联系。)
————————————————————汽车应用———————————————————
——————————————————电子电器应用——————————————————
部分型号部分物性表
EVA (ethylene vinyl acetate copolymer #) /1044/ Mubolaikesi snow
Use: Film
Feature preparation: VAC content is 3.5%, stable air cushion film.
Important beters: melt flow rate: 0.5 g/10min density: 0.929 g/cm3
Manufacturer: United States snow Mubolaikesi company
EVA (ethylene vinyl acetate copolymer #) /V4610H/ Yangzi BASF
Use: foaming
Important beters: melt flow rate: 1.95 g/10min VEKA softening point: 62 centigrade filler content: 18%
Manufacturer: Yangzi Petrochemical BASF Co., Ltd.
EVA (ethylene vinyl acetate copolymer #) /V3510K/ Yangzi BASF
Use: other
Important beters: melt flow rate: 4 g/10min tensile strength: 10 MPa breaking elongation: 550% VEKA softening point: 65 Centigrade filler content: 13%
Manufacturer: Yangzi Petrochemical BASF Co., Ltd.
EVA (ethylene vinyl acetate copolymer #) /E182L/ Han Hua Total
Application: coating
Important beters: melt flow rate: 15 g/10min tensile strength: 9.8 MPa elongation at break: 600% bending modulus: 98 MPa hardness: 15 VEKA softening point: 51 DEG heat debing temperature: 85 C, embrittlement temperature: -70 C.
Manufacturer: Han Hua Total Ltd.
EVA (ethylene vinyl acetate copolymer # Lotte chemical /VS430/)
Use: foaming
Characteristic notes: technological, mechanical, and particle foam characteristics
Important beters: melt flow rate: 2.5 g/10min density: 0.939 g/cm3 tensile strength: 13 MPa breaking elongation: 670% hardness: 38 VEKA softening point: 64 C
Manufacturer: Korean Music Corporation
EVA (ethylene vinyl acetate copolymer # Lotte chemical /VS440/)
Use: foaming
Characteristic notes: technological, mechanical, and particle foam characteristics
Important beters: melt flow rate: 2.2 g/10min density: 0.935 g/cm3 tensile strength: 13 MPa breaking elongation: 700% hardness: 40 VEKA softening point: 62 C
Manufacturer: Korean Music Corporation
EVA (ethylene vinyl acetate copolymer #) /11207/ America flintcomb ash
Use: Film
Characteristic notes: excellent toughness, good heat resistant seal under low temperature conditions
Important beters: melt flow rate: 4 g/10min density: 0.931 g/cm3 tensile strength: 16 MPa breaking elongation: 750% hardness: 46 VEKA softening point: 70 C
Manufacturer: American flint Hill resources
EVA (ethylene vinyl acetate copolymer # /UE624000/ Leander Basil)
Use: other
Important beters: melt flow rate: 2.1 g/10min tensile strength: 30.3 MPa fracture elongation: 560% hardness: 91 VEKA softening point: 65 C embrittlement temperature: -76 C
Manufacturer: Liane Basel Industrial Corporation
EVA (ethylene vinyl acetate copolymer #) /ML 20/ of Italy
Use: other
Characteristic notes: good chemical resistance
Important beters: melt flow rate: 2.5 g/10min tensile strength: 7 MPa flexural modulus: 100 MPa hardness: 43 VEKA softening point: 78 C embrittlement temperature: -80 C
Manufacturer: Italy Eni
EVA (ethylene vinyl acetate copolymer #) /ML 40/ of Italy
Use: other
Characteristic notes: good elasticity and flexibility
Important beters: melt flow rate: 2.5 g/10min tensile strength: 6 MPa flexural modulus: 60 MPa hardness: 40 VEKA softening point: 63 C embrittlement temperature: -80 C
Manufacturer: Italy Eni
给您选择我们的理由：
1：全新原产原包，品质保证。无副牌、水口料。
2：价格合理，诚信经营。
3：可全国供货。免费提供外包装保护袋。（广东省内免费送货上门）。
4：完善的售后服务，可提供加工参数，塑胶原料相关报告。
郑重承诺:本公司所售原料均为原厂原包装正牌料,杜绝一切副牌料,水口料以次充好,不开封，无破损！（价格未能及时更新，可能与实际价格有出入，以口头或书面报价为准）
