GHR-DS 高精度食用油大小剂量通用灌装机 粘稠灌装机

GHR-DS<\/span>食用油<\/span>灌装机<\/span>,<\/span>采用活塞定量方式<\/span>,<\/span>气压驱动及电子控制技术<\/span>,<\/span>设计独特<\/span>,<\/span>操作调试容易简便<\/span>,<\/span>本机采用双速控制灌装流速<\/span>,<\/span>先快装后慢装<\/span>,<\/span>即能保证有**的灌装速度<\/span>,<\/span>又能够防止灌装过程的上冲冒溢<\/span>,<\/span>使用气动内封闭式灌装阀嘴可有效防止灌装过程的滴漏。本机轻便灵活<\/span>,<\/span>即可独立使用也可与压盖机、封口机、输送机联机使用<\/span>,<\/span>广泛用于各种油类<\/span>.<\/span>、饮料、调味品、及其它液体产品的定量灌装。机壳采用不锈钢制造<\/span>,<\/span>美观卫生。该机为经济实用型<\/span>,<\/span>它结构简单<\/span>,<\/span>易操作<\/span>,<\/span>是中小型企业理想的生产设备。<\/span><\/span><\/p>

二、主要技术参数<\/span>:<\/span><\/span><\/p>

灌装容量<\/span>:  0.5—5<\/span>（升）<\/span><\/span><\/p>

灌装速度<\/span>:  200—3000<\/span>桶<\/span>/<\/span>小时（视容量大小、粘度而定）。<\/span><\/span><\/p>

灌装精度<\/span>: <\/span>≤±<\/span>0.5%<\/span>（按设计最大容量计）。<\/span><\/span><\/p>

工作电压<\/span>:  220v<\/span><\/span><\/p>

工作压力<\/span>:  0.4—1.0<\/span>兆帕（需方自备）。<\/span><\/span><\/p>

功率<\/span>:     <\/span>＜<\/span>300w<\/span>（不包括空气压缩机）。<\/span><\/span><\/p>

耗气量<\/span>:   <\/span>＜<\/span>0.2<\/span>立方米<\/span>/<\/span>分钟。<\/span><\/span><\/p>

 <\/span><\/p>

三<\/span>.<\/span>按装调试<\/span>:<\/span><\/span><\/p>

1<\/span>、<\/span>     <\/span>首先仔细检查电器及连接线有无松动脱落。设备在运输过程中有无碰撞造成损坏或其它螺丝有无松动脱落等现象。<\/span><\/span><\/p>

2<\/span>、<\/span>     <\/span>分别接通<\/span>220v<\/span>电源<\/span>,<\/span>按通气路将压力调整在<\/span>0.4—0.6Mpa<\/span>之间（本机在出厂前已调好）。<\/span><\/span><\/p>

3<\/span>、<\/span>     <\/span>根据瓶子高度调整好灌装嘴的高度<\/span>,<\/span>一般瓶口距离灌装嘴<\/span>5—10<\/span>毫米。根据所要求的灌装容量调整灌装量<\/span>,<\/span>通过调整气缸上带有容量刻度的磁性开关可改变灌装容量<\/span>,<\/span>通过量杯或电子称进行标定<\/span>,<\/span>再细调其精度<\/span>,<\/span>直至符合你的要求<\/span>,<\/span>最大误差不大于±<\/span>0.5%<\/span>（按设计最大容量计）。根据不同粘度的液体可适当调节灌装流速<\/span>,<\/span>如粘度大容易起泡沫的液体应减小流速<\/span>,<\/span>可通过调节气路上的节流阀来改变气缸的运行速度<\/span>,<\/span>使灌装流速变小。<\/span><\/span><\/p>

4<\/span>、<\/span>     <\/span>打开电源开关、按动灌装开关<\/span>,<\/span>机器便会自动吸液—出液—关阀停止等工作程序。<\/span><\/span><\/p>

四<\/span>. <\/span>常见故障的排除<\/span>:<\/span><\/span><\/p>

1<\/span>、不工作<\/span>:<\/span>电源未接通或无气压<\/span>,<\/span>检查电源、气源。<\/span><\/span><\/p>

2<\/span>、灌装容量误差大<\/span>:<\/span><\/span><\/p>

⑴<\/span>、<\/span>料液缸有空气<\/span>,<\/span>长按工作开关进行排气。<\/span><\/span><\/p>

⑵<\/span>、<\/span>进液管道密封不严有漏气<\/span>,<\/span>卡紧连接管。<\/span><\/span><\/p>

⑶<\/span>、<\/span>进液止回阀有脏物<\/span>,<\/span>拆下清洗止回阀。<\/span><\/span><\/p>

⑷<\/span>、<\/span>操作或灌装速度太快<\/span>,<\/span>适当变慢速度。<\/span><\/span><\/p>

⑸<\/span>、<\/span>料液缸液位高<\/span>,<\/span>液位应在<\/span>0—1.5<\/span>米（高压高液位灌装应另外定制）。<\/span><\/span><\/p>

⑹<\/span>、<\/span>料液缸密封圈磨损<\/span>,<\/span>更换密封圈。<\/span><\/span><\/p>