FORTRON 1140L4 SF3001

长期供应FORTRON PPS 1140L4 SF3001价格合理,诚信经营，可全国供货（广东省内 免费送货上门）。

“十年老店，完备售后，信誉信赖” 是专业塑胶原料供应商

本司货源稳定充足，发货准时，交期和质量均有保障！
根据客户要求，可提供塑胶原料相关报告。如：ROHS(SGS)报告，UL认证，材质证明及物质安全资料表（MSDS）！

欢迎来电咨询7*24全天候服务热线：13686017791 易小姐 QQ：335171600

---

  

介绍———————— 

      pps为一种白色粉末，平均分子量为0.4-0.5万，密度为1.3-1.8克每立方厘米，pps有十分优异的热性能。添加玻璃纤维增强后的热性能指标更高，在232摄氏度经5000h的热老化后，如玻璃纤维、碳纤维、填料等来增强其力学性能，改性后的pps能在长期工作负荷和热负荷的作用下保持高的力学性能和尺寸稳定性，因而可应用于温度高的受力环境中。
　　pps的介电常数很小，介电损耗相当低，表面电阻率和体积电阻率对频率、温度、湿度的变化不敏感，是优良的电绝缘材料，它的耐电弧时间也较长，pps的化学稳定性相当好，除了受强氧化酸，如浓硫酸、浓硝酸和王水的侵蚀外，它不受绝大多数酸碱盐的侵蚀，具有接近于PTFE的化学稳定性。在低于175摄氏度时不溶于任何已知的有机溶剂，pps与一般有机溶剂接触时不会出现塑件开裂现象。
耐化学性能：目前尚未发现可在200℃以下溶解聚苯硫醚的溶剂，对无机酸、碱和盐类的抵抗性极强。不耐氯代联苯及氧化性酸、氧化剂、王水、过氧化氢及次氯酸钠等。
　　PPS的耐辐射性好，耐辐射达到Gy 1×108，是其它工程塑料无法比拟的新材料，在电子、电气、机械、仪器、航空、航天、军事等特别是原子弹、中子弹领域，是作为耐辐射唯一理想的优良材料。
　　PPS本身的化学结构相当稳定，而且含有阻燃性的元素——硫，因此，PPS具有优异的耐燃性。将试片点燃，调整氧气与氮气的流速观察燃烧情形。而刚好让试片持续燃烧的氧气浓度便是极限氧气指数，其值越高，表示耐燃性越佳。纯PPS的极限氧气指数可高达44，也就具有优良的耐燃性。含填充剂或玻璃纤维的PPS的极限氧气指数更高，其耐燃性更佳。
　　纯PPS在厚度为0.8mm时便可通过UL-94 V0级。基本上，除了少数等级如超韧系列之外，各种等级PPS的UL94燃烧性都是属于V-0级，在UL 94燃烧性中已是最佳的等级了。超韧系列PPS含有一些增韧剂，会牺牲一些耐燃性。
　　纯PPS及未添加导电物的PPS等级皆具有优良的电气绝缘性质。添加碳纤维的PPS等级则有相当低的体积电阻系数。

Physical Properties	Metric	English	Comments
Density	1.60 g/cc	0.0578 lb/in³
Mechanical Properties	Metric	English	Comments
Hardness, Rockwell R	120	120
Tensile Strength, Ultimate	120 MPa	17400 psi	ASTM D638
Tensile Strength, Yield	120 MPa	17400 psi	ASTM D638
Elongation at Break	1.0 %	1.0 %	ASTM D638
Modulus of Elasticity	13.0 GPa	1890 ksi	ASTM D638
Flexural Yield Strength	170 MPa	24700 psi	ASTM D790
Flexural Modulus	12.0 GPa	1740 ksi	ASTM D790
Compressive Yield Strength	170 MPa	24700 psi	ASTM D695
Poissons Ratio	0.396	0.396
Shear Modulus	4.66 GPa	676 ksi	Calculated
Shear Strength	82.7 MPa	12000 psi
Izod Impact, Notched	0.530 J/cm	0.993 ft-lb/in	ASTM D256
Izod Impact, Unnotched	2.40 J/cm	4.50 ft-lb/in	ASTM D256
Taber Abrasion, mg/1000 Cycles	23	23	CS-17 wheel; 1 kg

 

其他型号参数与生产商——————————

PBT (polybutylene terephthalate polyester #) /GRTB-30/ Suzhou morning
Use: other
Important beters: density: 1.63 g/cm3 water absorption: 0.03% molding shrinkage: 0.55% notched impact strength: 0.08 tensile strength: 130 MPa bending strength: 175 MPa hardness: 119 hot debation temperature: 210
Manufacturer: Wuxian, Suzhou, the dawn of new chemical materials plant
PBT (polybutylene terephthalate polyester #) /1100-104S/ Taiwan Changchun
Use: other
Important beters: melt flow rate: 20 g/10min density: 1.31 g/cm3 water absorption: 0.06% tensile strength: 55.86 MPa bending strength: 86.24 MPa bending modulus: 2450 MPa thermal debation temperature: 60
Manufacturer: Changchun Taiwan enterprise group
PBT (polybutylene terephthalate polyester #) /D202/ Taiwan Xinguang
Use: other
Important beters: density: 1.4 g/cm3 water absorption: 0.08% molding shrinkage: 1.25% notched impact strength: 4 elongation at break: 6% bending strength: 900 MPa bending modulus: 26000 MPa hardness: 118 thermal debation temperature: 70
Manufacturer: Xinguang synthetic fiber Limited by Share Ltd
PBT (polybutylene terephthalate polyester #) /G10/ Shandong Yucheng
Use: other
Important beters: density: 1.52 g/cm3 molding shrinkage: 0.8% notched impact strength: 50 tensile strength: 100 MPa elongation at break: 3% bending strength: 130 MPa bending modulus: 3700 MPa thermal debation temperature: 210
Manufacturer: Shandong Yucheng Plastic Industrial Co. Ltd.
PBT (polybutylene terephthalate polyester #) /G20/ Shandong Yucheng
Use: other
Important beters: density: 1.56 g/cm3 molding shrinkage: 0.6% notched impact strength: 60 tensile strength: 100 MPa elongation at break: 3% bending strength: 160 MPa bending modulus: 6000 MPa thermal debation temperature: 215
Manufacturer: Shandong Yucheng Plastic Industrial Co. Ltd.
PBT (polybutylene terephthalate # polyester) /3011G20/ Yuyao Dragon
Use: other
Important beters: water absorption: 0.07% molding shrinkage: 0.4% notched impact strength: 8 tensile strength: 110 MPa elongation at break: 4% thermal debation temperature: 202
Manufacturer: Yuyao Tenglong Plastic Co. Ltd
PBT (polybutylene terephthalate polyester #) /T301/ Ningbo Futian
Use: other
Characteristic note: general level
Important beters: density: 1.5 g/cm3 molding shrinkage: 0.7% notched impact strength: 70 tensile strength: 90 MPa elongation at break: 4% bending strength: 140 MPa bending modulus: 4000 MPa thermal debation temperature: 170
Ningbo Fu Tian Engineering Plastics Co., Ltd.
PBT (polybutylene terephthalate polyester #) /T303/ Ningbo Futian
Use: other
Characteristic note: general level
Important beters: density: 1.6 g/cm3 molding shrinkage: 0.4% notched impact strength: 90 tensile strength: 125 MPa elongation at break: 3% bending strength: 190 MPa bending modulus: 9500 MPa thermal debation temperature: 210
Ningbo Fu Tian Engineering Plastics Co., Ltd.
PBT (polybutylene terephthalate polyester #) /B-4406/ Germany BASF
Use: other
Characteristic remark: Ultradur?
Important beters: density: 1.45 g/cm3 water absorption: 0.25% molding shrinkage: 1.5% thermal debation temperature: 60
Manufacturer: German Basf Inc
PBT (polybutylene terephthalate # polyester) /1800/ Shenzhen optimization
Use: other
Characteristic remark: environmental protection
Important beters: melt flow rate: 20 g/10min density: 1.45 g/cm3 absorption rate: 0.07% molding shrinkage rate: 1.7% notched impact strength: 4 tensile strength: 50 MPa flexural strength: 85 MPa flexural modulus: 2200 MPa hardness: 90 thermal debation temperature: 55 degrees
Shenzhen optimization engineering plastics Co., Ltd.